#Iclock 660 manual manual
#Iclock 660 manual software
#Iclock 660 manual professional
#Iclock 660 manual download

Inova OnTime Digital Clock Owner's Manual Section 5: Digital Clock Configuration Once a clock is installed, the next step is to confirm or set the configuration. Repeat for the second clock if two clocks are being installed back-to-back. Pull the clock slightly downwards until the unit is seated.

Position the keyhole slots located on the rear of the clock over the mounting tabs on the clock mount. Lift the clock into place and insert the data cable into the jack located on the back of the clock. Securely attach the mounting unit to the wall using fasteners suitable for the wall surface. Inova OnTime Digital Clock Owner's Manual 5. Using the template provided, mark the location where the clock is to be mounted, making sure the center is located over the data cable outlet. This procedure requires a mounting kit, Model ONTKIT. Inova OnTime Digital Clock Owner's Manual Cantilever Mounting – Single or Double The following is a recommended procedure for cantilever mounting. Supplement the ONTKIT with two suitable locknuts and a length of ¾ “ 1. The illustration above suggests a recommended mounting means for a pendant mount of one or more OnTime Digital Clock. This procedure requires a mounting kit – Model ONTKIT - and some additional hardware. Inova OnTime Digital Clock Owner's Manual Pendant Mounting – Single or Double The following is a recommended procedure for pendant mounting. Surface Mounting The following is a recommended procedure for surface mounting. The procedures for surface mounting, pendant mounting, and cantilever mounting are included on the following pages. Once you have removed and inspected the clock, you have several mounting options to consider. Inspect the clock and report any damage to Inova Solutions, Inc.

Inova OnTime Digital Clock Owner's Manual Section 4: Unpacking and Installation The OnTime Digital Clock arrives fully assembled in a single package. Inova OnTime Digital Clock Owner's Manual Section 3: Technical Specifications The OnTime Digital Clock is currently available in the models listed in the table below with the following specifications. Observe normal safety precautions and use appropriate safety equipment (safety glasses, gloves, ladders, etc. To prevent personal injury, damage to the unit, or other harm, read this manual in its entirety before installing or operating the OnTime Digital Clock. Inova OnTime Digital Clock Owner's Manual Section 2: Safety Instructions Before installing or operating any OnTime Digital Clock, it’s important that you carefully read and understand the following safety considerations. It’s the same technology that powers Voice over IP phones. PoE is an exciting and relatively new technology that allows devices to get both power and data over standard network cabling. Inova OnTime Digital Clock Owner's Manual Section 1: Introduction to Inova OnTimeTM Digital Clocks The Inova OnTimeTM Digital Clock brings all the advantages of Power over Ethernet (PoE) technology to the marketplace in a real-time synchronized system of clocks. Inova OnTime Digital Clock Owner's Manual Figures Figure 1: Pendant Mounting. 19 Section 9: Recording Static IP Addresses or Host Names. Inova OnTime Digital Clock Owner's Manual Section 8: Troubleshooting. Inova OnTime Digital Clock Owner's Manual Table of Contents Section 1: Introduction to Inova OnTimeTM Digital Clocks. assumes no liability resulting from any errors or omissions in this manual, or from the use of the information contained herein. While reasonable efforts have been taken in the preparation of this document to insure its accuracy, Inova Solutions, Inc. in the United States and/or other countries. Inova OnTime Digital Clock Owner's Manual Inova OnTimeTM Digital Clock Owner’s Manual Revision 008 Inova Part#: 715412 Inova OnTime is a trademark of Inova Solutions, Inc. New Push SDK 3.Inova OnTimeTM Digital Clock Owner’s Manual.

#Iclock 660 manual download

Pendrive download structure defined by user.

#Iclock 660 manual professional

Professional Firmware Version with advanced features.

For access control, it allows time zones and groups and the relay can be connected to lock or external siren.

#Iclock 660 manual software

It can connect to T&A management software by Ethernet or USB port (optionally it can work with WiFi and GPRS), and also operates on standalone mode, downloading data by USB pendrive. The color TFT display offers users easy menu management. Easy to install, and with a modern design, it is the perfect solution for all kinds of installations. IClock S680 P Proximity T&A Terminal iClock S680 is a Time & Attendance and access control terminal with incorporated EM proximity card reader and 3’5 TFT display.